ECU Pinout Diagramm benötigt - Druckversion +- TransSport Portal (http://www.pontiac-trans-sport.de) +-- Forum: ab 1997: Chevrolet Trans Sport / Pontiac Montana / Oldsmobile Silhouette / Buick GL8 (http://www.pontiac-trans-sport.de/forumdisplay.php?fid=4) +--- Forum: ab '97: Elektrik + Diagnose + Klima (http://www.pontiac-trans-sport.de/forumdisplay.php?fid=26) +--- Thema: ECU Pinout Diagramm benötigt (/showthread.php?tid=430) |
ECU Pinout Diagramm benötigt - SvenKuhne - 23.10.2016 Hallöchen Ihr lieben.... Ich bin auf der Suche nach dem einen oder anderen Fehlerteufel in einem 2002er AWD. Gibt es noch jemanden der evtl. eine Pinout vom Motorsteuergerät hat ??? Ich bräuchte einmal wenn es geht bitte die komplette Auflistung der Clear-Pins und der Blue-Pins Wäre super wenn das jemand hat und als Bilder eben posten könnte Die Suche im Netz bringt irgendwie nicht das gewünschte Ergebnis... Lieben Dank schon mal RE: ECU Pinout Diagramm benötigt - MR1972 - 24.10.2016 Blau: 1 Low Reference 2-3 Not Used 4 1-2 Shift Solenoid Valve Control 5 High Speed Cooling Fan Relay Control 6 LowSpeed Cooling Fan Relay Control 7 Camshaft Position Signal 8 Low Resolution Engine Speed Signal 9 Medium Resolution Engine Speed Signal 10 5 Volt Reference 11 Not Used 12 HO2S Low Signal 13 Low Reference 14-15 Not Used 16 Ground 17 Low Reference 18 Not Used 19 Off/Run/Crank Voltage 20 Battery Positive Voltage 21 Not Used 22 Trans Fluid Pressure Switch Signal A 23-27 Not Used 28 HO2S Low Signal 29 Oxygen Sensor A Low 30 TCC Brake Switch/ Cruise Control Release Signal 31 Low Reference 32 EGR Solenoid Control 33 KS Signal 34-37 Not Used 38 IAC Coil B High Control 39-42 Not Used 43 Fuel Injector 1 Control 44 2-3 shift Solenoid Valve Control 45 Air Solenoid Control 46 Fuel Injector 3 Control 47 Fuel Injector 2 Control 48 Low Reference 49-52 Not Used 53 IC Timing Signal 54 IC Timing Control 55 Vehicle Speed Signal 56 Ground 57 Ground 58 Not Used 59 ECM/PCM/VCM Class 2 Serial Data 60 Ground 61 Low Reference 62 AT/ISS Low Signal 63 AT/ISS High Signal 64 VSS High Sigtnal 65 VSS Low Signal 66-67 Not Used 68 Transaxle Range Switch Signal B 69 MAF Sensor Signal 70 Not Used 71 Required Torque Signal 72 Cruise Control Inhibit Signal 73 Fuel Injector 5 Control 74 Axle Actuator Control 75 Not Used 76 EVAP Canister Purge Solenoid Control 77-78 Not Used 79 Fuel Injector 6 Control 80 Low Reference Durchsichtig: 1 Not Used 2 EVAP Canister Vent Valve Control 3 Fuel Pump Relay Control 4 EGR Valve Feed Control 5 MIL Control 6 Not Used 7 IAC Coil A High 8 Not Used 9 Delivered torque 10 HO2S Sensor 1 Signal High 11 HO2S Sensor 2 Signal High 12-15 Not Used 16 Transaxle Range Switch Signal P 17 Trans Fluid Pressure Switch Signal C 18 Transaxle Range Switch Signal A 19 Oil Pressure Switch Signal 20-21 Not Used 22 A/C Request Signal 23 Crank Voltage 24 Ignition 1 Voltage 25 MAP Sensor Signal 26 ECT Sensor Signal 27 A/C Refrigerant Pressure Sensor Signal 28 EGR Valve Position Signal 29 Not Used 30 5 Volt Reference 31-32 Not Used 33 5 Volt Reference 34 5 Volt Reference 35 Low Reference 36 Not Used 37 HO2S Heater Low Control 38 Not Used 39 A/C Compressor Clutch Relay Control 40-41 Not Used 42 Fuel Injection 4 Control 43 Not Used 44 IAC Valve A Low 45 PC Solenoid Valve High 46 PC Solenoid Valve Low 47-48 Not Used 49 IAC Valve B Low Control 50 Intake Air Temperature Sensor 51-54 Not Used 55 Fuel Tank Pressure Sensor Signal 56 Transaxle Range Switch Signal C 57 Trans Fluid Pressure Switch Signal B 58 Engine Oil Level Indicator Signal 59 Cruise Control Engaged Signal 60 Not Used 61 Generator Turn On Signal 62 Not Used 63 TCC Release Switch Signal 64-65 Not Used 66 TP Sensor Signal 67 Not Used 68 TFT Sensor Signal 69 Fuel Level Sensor Signal 70 12 Volt Reference 71 Not Used 72 12 Volt Reference 73 Low Reference 74 Low Reference 75 Air Pump Relay Control 76 Starter Enable Relay Control 77 Not Used 78 TCC PWM Solenoid Valve Control 79 Not Used 80 Low Reference RE: ECU Pinout Diagramm benötigt - SvenKuhne - 24.10.2016 Super, danke dir für die passende Belegung... Ich habe einige schon durch nachmessen herausgefunden Und von daher ist das hier die richtige für meine derzeitige Baustelle.... PN habe ich dir auch schon geschickt. |